Maintenance of the machine is an extremely important and regular work, it should be the operation and maintenance and other very closely, there should be full-time staff on duty checks.
One. Machine maintenance:
1, bearing China Plastic Crusher bearing shoulder all the load of the machine, so good lubrication of the bearing life of a great relationship, it directly affects the life of the machine and the operation rate, which requires injection of the oil must be clean, seal must have good The main oiling the machine at the (1) Turn the bearing (2) roller bearings (3) All Gear (4) activities bearings, sliding plane.
2, the newly installed tires prone to loosening must always be checked.
3, note that the various parts of the machine is working properly.
4, pay attention to check the wear wear parts, and pay attention to either replace the worn parts.
5, put the device chassis plane activities, should be out dust and other objects in case the material could not have broken in the end when the active bearing can not move the shelves, resulting in a serious accident.
6, the bearing temperature rise, the reasons should be immediately stopped and checked to be eliminated.
7, when running the gears if the impact of the sound check should be immediately stopped and eliminated.
II. Installation test
1, the device should be installed at the level of the concrete foundation, and with the anchor bolts fixed.
2, the installation should pay attention to the vertical and horizontal main body.
3, after the installation check to see whether or loose bolts are tightened and the main doors, where do the tightening.
4, according to the power equipment, power cord and control switch configuration.
5, inspection is completed, the empty load test, production test can be carried out properly.

New composite material is produced in the traditional basis of a new generation of sheet material, which is a composite material. Composite materials including organic materials and inorganic materials, composites,
Metallic composite materials and non-metallic materials, and other similar materials, the complex of the composite material makes the varieties and functions of civil engineering materials more diverse.
1, Class ferrocement sandwich plate
It is based on two pieces of steel mesh to polyurethane, polystyrene, urea-formaldehyde resin foam, mineral wool or glass wool and other lightweight core material in the middle, between two pieces of steel mesh to slope
Through the core material of the “s” shaped wire connected to each other to form a stable three-dimensional truss structure, and then wipe the surface of cement mortar on both sides, or other decorative finishes.
Ferrocement sandwich plate full advantage of the core material for thermal insulation and light features, but also has concrete performance on both sides, so the construction has
The flexibility of wood and concrete surface quality.
China Plastic Crusher good warm function, with good sound insulation, anti-freeze is good, strong, and the construction of seismic energy consumption is low.
2, the color steel sandwich panel material
Color steel sandwich panel material is mineral wool rigid foam core material or structure, color pressure in the glue on both sides of galvanized steel, in which the exposed surface of color coated steel sheet
Advanced colored plastic coating, it has a good weather resistance and corrosion resistance. Indicate the structure

Plastic processing industry used the general term for all types of machinery and equipment. Some of the fluid and solid transport, separation, crushing, grinding and drying versatile machinery and equipment, also in the plastics processing industry occupies an important position, so often as the plastics machinery. Modern design and manufacture of plastic machinery, in addition depends on the mechanical engineering and materials science development, especially with the plastic construction is closely related to the progress of theoretical research.
With the continuous development of manufacturing industry presses, presses rising foreign sales, exports from the original countries in Southeast Asia, the Middle East to Europe, the United States that developed countries and regions. In order to better cope with technical barriers to trade presses to expand our international market share, many companies have carried out presses CE, UL and other safety certification. However, do not quite understand because of the safety certification, resulting in the choice of certification bodies and there are many problems in the certification process, and even fooled. As
China Plastic Crusher only one national plastic machinery inspection agencies, to guide development of the industry shoulder the heavy responsibility and obligation to the need to use the center professional and technical capacity, for the majority of presses manufacturers introduce safety certification of knowledge, thereby promoting greater industry presses Good to overcome technical barriers to trade and improve international competitiveness. Taking into account the current majority of enterprises are in dire need of the EU’s CE safety certification security certification, the following will serve as introduced in detail.
CE is a French Conformitē Europēeme (European Conformity Assessment) acronym, is unique to the mandatory European safety mark. Assess whether the EU market products based on circulation, whether the product affixed CE mark. Once the product affixed CE mark to show that the product complies with the EU basic public safety, health, environmental and consumer protection requirements. EU’s existing 27 member states: Belgium, Cyprus, Czech Republic, Denmark, Germany, Greece, Spain, Estonia, France, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Austria, Poland, Portugal, Romania, Slovakia, Slovenia, Finland, Sweden and the UK, and anxious to join the EU in Turkey. Up to now, the EU issued a total of 22 instructions (instructions can be defined as European law, higher than the technical regulations of the Member States), the products involved are: electronics and electric products, machinery and equipment, simple pressure vessels, toys, construction products, personal protective equipment, medical equipment, gas appliances, pressure equipment. Plastic machinery with manual loading by plastic injection or compression molding machine for its high level of risk by the EU Machinery Directive as dangerous machinery, must be Notified Body (EU authority) inspection of products before the implementation of EC CE mark posted and sold and used in the EU.

UPVC drainage pipe
UPVC pipes plastic pipe industry output in China accounts for about 50% of China’s most widely used application of the earlier, the user is most familiar with the plastic pipe. However, in testing, we found that there is a lot of UPVC drainage problems.
This is because the poor performance of PVC resin processing narrow, very Gou carved molding conditions, so the UPVC pipe production enterprises, to find the best additives (such as stabilizers, modifiers, lubricants, fillers, etc.) to study the optimal ratio and reasonable process is to ensure the quality of the premise China Plastic Crusher now introduce some common problems of plastic pipe.
A plastic pipe problem: poor tensile strength and toughness. Good tensile strength of UPVC pipes should be obvious yield curve, higher elongation, while the difference of plastic pipe often engendered brittleness, low elongation fracture easily understood.
Plastic pipe problem II: impact poor. Detected by GB/T5836.1-92 drop hammer impact test standards, detected for many years, once through rate was only less than 50% or even 10 times the impact of many products, all broken.
Plastic tubing to the three: softening temperature is lower, easy-to-case thermal deformation. Performance in the test performance, that is, the lower Vicat softening temperature (less than 79), and some manufacturers to improve the softening temperature, simply fill in the ingredients to increase the amount of time, this can indeed improve the softening temperature, but the other pipe properties, especially impact resistance, tensile strength, toughness greatly reduced, so to improve the softening temperature, with little or reduced without reducing other properties to be selected in the additives, ratio of raw materials, production technology, and production machinery make an effort not to be taken lightly.
UPVC Water Supply Pipe
UPVC pipe, in accordance with the national standard GB/T10002.1-1996 to detect the value of the hydraulic tests require a higher performance standard, which UPVC water supply pipe production company made very high demands. Eccentricity is one of the common plastic pipe, it will lead to the production out of the plastic pipe wall thickness nonuniformity is large, which not only cause the waste of raw materials, and make it difficult to meet the test performance of the hydraulic loop stress 42MPa at the request of plastic pipe production line will significantly affect the operation. So which requires manufacturers not only make good material ratio, qualified enterprises line detection equipment should be installed at any time to adjust the size of plastic pipe deviation.

Hopper trailer behind the dump truck, dump truck from the feed and traction, for paving operations. Hopper supported on rollers on the front, stone pavers, such as a short distance hauling, the rear bearing on the skid, and to reduce than the pressure on the foundation and increase shop floor flatness. Both sides of the rear wall of the hopper is also equipped with a wider side hinged so as to adjust the paving width. Stone paver, such as a short distance haulage, can be run into the rear wheel skid to traction drag. Stone paver hopper capacity of the main technical parameters, paving the width and thickness.
China Plastic Crusher use in the hydraulic system to do maintenance work, you can greatly reduce the failure. General should note the following:
1 hydraulic oil in hydraulic tank before adding, containers should be used to clean oil, hydraulic oil shall be added after filtration of hydraulic oil filter tank; hydraulic oil replacement cycle, as determined by the quality of used oil (usually replaced every 1000h); replacement of hydraulic oil should be carried out under the operating temperature; in order to ensure good thermal hydraulic system, hydraulic oil cooler should be cleaned regularly.
2 Construction of the asphalt paver generally poor environment, the replacement cycle of the hydraulic oil filter should also be reduced (generally 750h is appropriate), the filter should be replaced with new check-ups, prohibited the use of deformed, contamination or rust filter.
3, start the engine in the daily work, should be idle for some time, and then manipulate the components of the implementation of the work, it is a good use of the hydraulic pump.
4 paver used due to the long, sometimes its hydraulic system parameters change, therefore, should regularly check hydraulic system parameter settings, time adjustment.

1 for residents: ① reduce storage bins kitchen cupboards, especially the odor; ② reduce the breeding ground for cockroaches, bacteria may be; ③ to clean up emissions from household waste into a clean, easy to work; ④ help keep the stairs rooms and living quarters of the health environment.
2, the sanitation department and property management is: ① to improve the sanitation work environment; ② reduce waste production; ③ Garbage Collector process to reduce secondary pollution; ④ reduce the difficulty and cost of handling garbage removal (This is especially important) .
3, on the municipal and traffic control departments that: ① increase the water content of organic matter in the perishable nature, conducive to the biological process of sewage treatment plants; ② reduce the number of garbage trucks and garbage pollution of water dripping on the road.
4, for the environment and recycling: ① kitchen waste to reduce the pollution of recyclable materials and improve resource recovery; ② landfills and incineration plants to improve the processing conditions to reduce leachate, methane, flue gas and other pollution emissions. Using the processor’s weaknesses are: residents will consequently increase the number of water and electricity expenses; widely used to clean up after the sewer network may increase; need to gradually adjust the treatment process of sewage treatment plants.
China Plastic Crusher safe operation:
1, the start and after the machine to normal operation, it allows uniform continuous feed crops.
2, the operation should pay attention to the motor, thresher speed, sound and bearing temperature.
3, feeding feeding when the operator should stand on the side of the mouth, clothes should be fastened sleeves, put on a mask and work hats. 4, feed, pay attention to whether there is a stone grain, Fusarium, tools, screws and other hard objects to avoid damage to the machine and cause personal injury.
5, the machine must not hang dynamic transfer belts, oiling, cleaning and troubleshooting.
6, found that the following issues should be off the engine and stop processing, ① electrical smoke, ② plug, ③ crush poor quality, ④ bearing overheating, more than 60 degrees.

VSM vertical double spiral ribbon mixer to mix with more Yunhe, so the material well-mixed, easy heating, cooling, lift, vacuum, explosion, spray and other auxiliary requirements, is the VSM can be achieved. VSM and VSH-D series conical ribbon mixer is mixing two completely different, whether it is operating or from the cleaning, or feeding, or after maintenance, VSM are preferred device, and it has a VSH-D Series advantages of conical ribbon mixer, and make up for the VSH-D series of conical spiral mixer with the shortcomings of the feed, discharge, vacuum, heating, cooling and other special devices optimized for a more stable and more convenient.
Application of high-speed mixer:
China Plastic Crusher particularly suitable for the solid – liquid, solid – powder, powder – powder, powder – a uniform mixture of liquid and efficient. Discharge valve: ball valve, butterfly valve, gate valve products are widely used to choose fine chemicals, feed, electronics, food, hard materials, ceramic materials, biology, medicine, non-metallic mining, building materials, paint, dye , fertilizers, and metal powders have a better mix. Crystal on the shear-sensitive powders, bulk product mix, mix the liquid into the solid.
Special high-speed mixer and environmental protection:
VSM has been started from the design were based on plant forms of simulation and optimization, so that equipment can fit a wider range of environments. Since the circumference of the low speed, the same applies to dangerous places. Displacement of the free flow of solid material is stirred. Cantilever axis and the bearing client does not contact with the materials. Stirring paddle and a very small gap between the vessel wall to prevent the bonding material. Standardized stirring drive box to ensure stable operation, low maintenance cost. GMP design, high-proof it can be heat or the cooling jacket, a conical valve quickly, each of which a large number of users after the test, so that you are using VSM in the process with more confidence.
For large machinery you are interested, please sign in http://www.weiruites.com to learn more about the products to improve the competitiveness of enterprises.

Filling the main line past the system has many shortcomings, including the purchase of high cost, large and heavy equipment, installation difficulties and high maintenance costs and other issues. But now, filling defects in the production line has been the advanced technology and a new filling line system instead of, more and more enterprises begin to pay attention and use the filling machine production line, they began to realize that filling production line to bring their benefits. filling production line in food, pharmaceutical, cosmetic manufacturers play an important role in optimizing filling production line is directly related to product quality and production efficiency, so manufacturers have to become a major topic of concern.
China Plastic Crusher major systems of the past, many drawbacks, including the purchase of high cost, large and heavy equipment, installation difficulties and high maintenance costs and other issues. But now, filling defects in the production line has been the advanced technology and a new filling line system instead of, more and more enterprises begin to pay attention and use the filling machine production line, they began to realize that filling production line to bring their benefits. filling production line in food, pharmaceutical, cosmetic manufacturers play an important role in optimizing filling production line is directly related to product quality and production efficiency, so manufacturers have to become a major topic of concern.
With empty boxes stacked on pallets, unloading pallets from the conveyor belt to the machine, remove the tray one by one, the box with the conveyor belt to unload boxes machine, will be removed from the box empty, empty containers by the conveyor belt to the washing machine box, the clean, territory to packing machine next to the bottles containing drinks into them. Removed from the unloading boxes empty bottle machine by a conveyor belt into the washing machine the other disinfecting and cleaning, the bottle inspection machine inspection, cleaning standards into line with the filling machine and capping machine. Drink from the bottle into the filling machine. Bottles and beverage bottles sealed and stamped by the capping machine conveyor to the labeling machine labeling, label stickers, ready to be sent packing machine into the box and then sent to the stack tray machine stacked on pallets into the warehouse.
Advantage of the production line filling machines for the manufacturing industry with excellent performance, stable and reliable filling line; material waste of less cost in mass production; program under the control of the production process, high efficiency; the production process of environmental pollution, etc. .

Waste plastic is in the civil, industrial and other purposes, the used and the final phase-out or replace the plastic down collectively. It is by means of re-use can be divided into: 1. Recycled plastic, 2. Re-processing plastic, 3. Recycled plastic, 4. Reusable plastic, 5. Recyclable plastic, 6. Not recycling plastics.
1. Recycled plastic by the factory reworked plastic molding, extrusion and other pre-processing, the use of scrap or defective mold of reprocessing plants in the preparation of the second thermoplastic.
2. Reprocessed plastics processors by the non-indigenous, with the preparation of industrial plastic waste thermoplastics.
3. Recycled plastics from the waste by cleaning and grinding of the products obtained in the plastic. Recycled plastics can be matched or not with filler, plasticizer, stabilizer, coloring agent.
4. Reusable plastic molding products can be repeatedly used, and performance to meet the requirements of the relevant provisions of the plastic.
5. Recyclable plastic waste, the permit has been recovered, and after some processing, it can be a class of plastics processing and utilization.
6. Not plastic waste recycling, the recycling process was not allowed to use a type of plastic.
Waste plastics can be used by some of the principles, China Plastic Crusher is to help you remove these headaches white trash is a good helper, after treatment, the waste plastics can be recycled in use. Can be a force for environmental protection, while the residual value of their own needs are.
Welcome http://www.weiruites.com, here are some everyday the necessary machinery.

Production areas (also known as line). For example, electronic electronic products, electronic devices factory, the production is past the pipe. production areas is specify collectively a specify of processes to enhance efficiency. just like a tv production, personal set up of loudspeakers set up from the motherboard personal, person showcase display screen equipment, every one among many processes collectively to arrive to be considered a production line.
In existing production, one China Plastic Crusher will be the real pressure from the shop, song retailer if an analogy, the production circulation areas are ordinarily a excellent note, in almost every nook of opportunity products, the international symphony. Commissioner is accountable for the production of these information the continuity and orderly production areas does not go incorrect responsibility. Therefore, excellent discussion skills, coordination and problem-solving potential are ordinarily a will probably have to have got quality.
Monitoring the development of production, handle the production process to create certain timely completion of project;
Production and technology, coordinating quality, logistics, discussion involving several departments to create certain smooth production;
With the assistance and outdoors suppliers of the appropriate departments to keep excellent communication, coordination and outdoors relations of production, deliver and support;
Suddenly time production, to coordinate the appropriate personnel, to address associated problems;
Performance evaluation composed weekly, monthly, quarterly production reports;
Organize, archive information.